ISO 17096:2015 Cranes — Safety — Load lifting attachments (Full)
20 thg 10, 2025 | 23:31

ISO 17096:2015 Cranes — Safety — Load lifting attachments (Full)



ISO 17096:2015 specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists, and manually controlled load manipulating devices as defined in Clause 3:


- plate clamps;


- vacuum lifters;


- self priming,


- non-self-priming (pump, venturi, turbine);


- electric lifting magnets (battery-fed and main-fed);


- permanent lifting magnets;


- electro-permanent lifting magnets;


- lifting beams/spreader beams;


- C-hooks;


- lifting forks;


- clamps.


ISO 17096:2015 does not specify the additional requirements for the following:


a) load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;


b) hazards resulting from handling hazardous materials (e.g. explosives, hot molten masses, radiating materials);


c) hazards caused by operation in an explosive atmosphere;


d) hazards caused by noise;


e) electrical hazards;


f) hazards due to hydraulic and pneumatic components.


ISO 17096:2015 does not cover attachments intended to lift people.


ISO 17096:2015 does not cover slings, ladles, expanding mandrels, buckets, grabs or grab buckets, and container spreaders.


CONTENTS:


Fo re wo rd ........................................................................................................................................................................................................................................i v

I n tro d u c ti o n ..................................................................................................................................................................................................................................v

1 S c o p e ................................................................................................................................................................................................................................. 1

2 N o r m a ti ve r e fe re n c e s ...................................................................................................................................................................................... 1

3 Terms and definitions..................................................................................................................................................................................... 2

4 S a fe ty r e q u i re m e n ts a n d / o r m e a s u r e s ......................................................................................................................................... 7

4.1 General requirements....................................................................................................................................................................... 7

4.1.1 Mechanical load bearing parts............................................................................................................................. 7

4.1.2 Controls.................................................................................................................................................................................... 7

4.1.3 Handles .................................................................................................................................................................................... 7

4.1.4 Requirements for slings which are integrated....................................................................................... 7

4.1 .5 Stability during storage.............................................................................................................................................. 8

4.2 Specific requirements for each category of attachment...................................................................................... 8

4.2.1 Plate clamps......................................................................................................................................................................... 8

4.2.2 Vacuum lifters..................................................................................................................................................................... 8

4.2.3 Lifting magnets...............................................................................................................................................................10

4.2.4 C-hooks..................................................................................................................................................................................11

4.2.5 Lifting forks.......................................................................................................................................................................11

4.2.6 Lifting beams....................................................................................................................................................................12

4.2.7 Clamps ...................................................................................................................................................................................13

5 Verification of the safety requirements and/or measures....................................................................................1 4

5.1 General........................................................................................................................................................................................................14

5.2 Proof of fatigue strength by testing....................................................................................................................................18

5.3 Minimum classification................................................................................................................................................................. 19

6 I n fo r m a ti o n fo r u s e .........................................................................................................................................................................................1 9

6.1 Instruction handbook.................................................................................................................................................................... 19

6.1.1 General information...................................................................................................................................................19

6.1.2 Specific information...................................................................................................................................................19

6.1.3 Guidance for maintenance....................................................................................................................................22

6.1.4 Verifications and inspections.............................................................................................................................23

6.2 Marking......................................................................................................................................................................................................23

6.2.1 General...................................................................................................................................................................................23

6.2.2 Minimum marking.......................................................................................................................................................23

6.2.3 Additional marking.....................................................................................................................................................23

A n n e x A (normative) General verification methods.........................................................................................................................2 5

A n n e x B (normative) Verification methods for plate clamps..................................................................................................2 7

A n n e x C (normative) Verification methods for vacuum filters..............................................................................................3 1

A n n e x D (normative) Verification methods for lifting magnets............................................................................................3 7

A n n e x E (normative) Verification methods for lifting beams..................................................................................................4 2

A n n e x F (normative) Verification methods for lifting forks.....................................................................................................4 4

A n n e x G (normative) Verification methods for clamps.................................................................................................................4 5






ISO 17096:2015 specifies safety requirements for the following non-fixed load lifting attachments for cranes, hoists, and manually controlled load manipulating devices as defined in Clause 3:


- plate clamps;


- vacuum lifters;


- self priming,


- non-self-priming (pump, venturi, turbine);


- electric lifting magnets (battery-fed and main-fed);


- permanent lifting magnets;


- electro-permanent lifting magnets;


- lifting beams/spreader beams;


- C-hooks;


- lifting forks;


- clamps.


ISO 17096:2015 does not specify the additional requirements for the following:


a) load lifting attachments in direct contact with foodstuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;


b) hazards resulting from handling hazardous materials (e.g. explosives, hot molten masses, radiating materials);


c) hazards caused by operation in an explosive atmosphere;


d) hazards caused by noise;


e) electrical hazards;


f) hazards due to hydraulic and pneumatic components.


ISO 17096:2015 does not cover attachments intended to lift people.


ISO 17096:2015 does not cover slings, ladles, expanding mandrels, buckets, grabs or grab buckets, and container spreaders.


CONTENTS:


Fo re wo rd ........................................................................................................................................................................................................................................i v

I n tro d u c ti o n ..................................................................................................................................................................................................................................v

1 S c o p e ................................................................................................................................................................................................................................. 1

2 N o r m a ti ve r e fe re n c e s ...................................................................................................................................................................................... 1

3 Terms and definitions..................................................................................................................................................................................... 2

4 S a fe ty r e q u i re m e n ts a n d / o r m e a s u r e s ......................................................................................................................................... 7

4.1 General requirements....................................................................................................................................................................... 7

4.1.1 Mechanical load bearing parts............................................................................................................................. 7

4.1.2 Controls.................................................................................................................................................................................... 7

4.1.3 Handles .................................................................................................................................................................................... 7

4.1.4 Requirements for slings which are integrated....................................................................................... 7

4.1 .5 Stability during storage.............................................................................................................................................. 8

4.2 Specific requirements for each category of attachment...................................................................................... 8

4.2.1 Plate clamps......................................................................................................................................................................... 8

4.2.2 Vacuum lifters..................................................................................................................................................................... 8

4.2.3 Lifting magnets...............................................................................................................................................................10

4.2.4 C-hooks..................................................................................................................................................................................11

4.2.5 Lifting forks.......................................................................................................................................................................11

4.2.6 Lifting beams....................................................................................................................................................................12

4.2.7 Clamps ...................................................................................................................................................................................13

5 Verification of the safety requirements and/or measures....................................................................................1 4

5.1 General........................................................................................................................................................................................................14

5.2 Proof of fatigue strength by testing....................................................................................................................................18

5.3 Minimum classification................................................................................................................................................................. 19

6 I n fo r m a ti o n fo r u s e .........................................................................................................................................................................................1 9

6.1 Instruction handbook.................................................................................................................................................................... 19

6.1.1 General information...................................................................................................................................................19

6.1.2 Specific information...................................................................................................................................................19

6.1.3 Guidance for maintenance....................................................................................................................................22

6.1.4 Verifications and inspections.............................................................................................................................23

6.2 Marking......................................................................................................................................................................................................23

6.2.1 General...................................................................................................................................................................................23

6.2.2 Minimum marking.......................................................................................................................................................23

6.2.3 Additional marking.....................................................................................................................................................23

A n n e x A (normative) General verification methods.........................................................................................................................2 5

A n n e x B (normative) Verification methods for plate clamps..................................................................................................2 7

A n n e x C (normative) Verification methods for vacuum filters..............................................................................................3 1

A n n e x D (normative) Verification methods for lifting magnets............................................................................................3 7

A n n e x E (normative) Verification methods for lifting beams..................................................................................................4 2

A n n e x F (normative) Verification methods for lifting forks.....................................................................................................4 4

A n n e x G (normative) Verification methods for clamps.................................................................................................................4 5




M_tả

M_tả

Chuyên mục:

Không có nhận xét nào: