TÀI LIỆU - Van cấp liệu lò (Bernard Controls)

The configuration panel of the INTEGRAL+ board allows to adapt the actuator at each particular application. Information to be transmitted and actuator behaviour configuration are set with switches and jumpers. The actuator is deliverable with standard configuration, or optional configuration if requested at order. The configuration can be easily changed on site. The jumper and switches settings can be reported in a table on page 39.


CONTENTS:

DRAWINGS  Page 3
1  INTRODUCTION  Page 4
2  CONFIGURATION  Page 4
3  POWER SUPPLY  Page 4
3.1  Actuator power supply  Page 4
3.2  Output power supplya   Page 5
4  ACTUATOR OPERATION  Page 5
4.1  Direction of rotation  Page 5
4.2  Closing type  Page 5
4.3  By-pass of open torque switch when starting to open from closed position  Page 6
4.4  Rotation reverse relay  Page 6
5  REMOTE CONTROL  Page 6
5.1  Dry contacts control  Page 7
5.2  Voltage control  Page 7
5.3  Single dry contact control  Page 7
5.4  Priority to open or to close  Page 8
5.5  Emergency control (ESD)  Page 8
5.6  Local control inhibition  Page 9
6  LOCAL CONTROL  Page 10
6.1  Self-holding local control  Page 10
6.2  Local stop  Page 10
6.3  General stop  Page 10
6.4  Local/remote selector padlock  Page 10
7  INDICATIONS  Page 11
7.1  Blinking indications  Page 11
7.2  Indication relay N°1  Page 12
7.3  Indication relay N°2  Page 12
7.4  Indication relay N°3  Page 12
7.5  Indication relay N°4  Page 13
7.6  Fault monitoring relay  Page 13
8  FUSES PROTECTION  Page 15
9  POSITIONER OPTION  Page 15
9.1  Input signal configuration  Page 15
9.1.1  Operation with signal 0-20mA  Page 15
9.1.2  Operation with signal 0-10V  Page 15
9.2  Operation direction configuration  Page 15
9.3  ‘Stay put’ function configuration  Page 16
9.4  Dead band adjustment  Page 16
9.5  Local operation  Page 16
9.6  Adjustment of 0%  Page 17
9.7  Adjustment of 100%  Page 17
9.8  Split range  Page 17
9.9  Operation with 4-20mA transmitter  Page 18
9.10  Remote control AUTO/ON-OFF  Page 18
10  LOCAL INDICATION OPTION  Page 18
11  TIMING CONTROL BOARD OPTION  Page 18
12  TROUBLESHOOTING INTEGRAL+ VERSION  Page 20
13  TROUBLESHOOTING OF POSITIONER VERSION  Page 23
14  USER’S SETTING  Page 50

LINK DOWNLOAD

The configuration panel of the INTEGRAL+ board allows to adapt the actuator at each particular application. Information to be transmitted and actuator behaviour configuration are set with switches and jumpers. The actuator is deliverable with standard configuration, or optional configuration if requested at order. The configuration can be easily changed on site. The jumper and switches settings can be reported in a table on page 39.


CONTENTS:

DRAWINGS  Page 3
1  INTRODUCTION  Page 4
2  CONFIGURATION  Page 4
3  POWER SUPPLY  Page 4
3.1  Actuator power supply  Page 4
3.2  Output power supplya   Page 5
4  ACTUATOR OPERATION  Page 5
4.1  Direction of rotation  Page 5
4.2  Closing type  Page 5
4.3  By-pass of open torque switch when starting to open from closed position  Page 6
4.4  Rotation reverse relay  Page 6
5  REMOTE CONTROL  Page 6
5.1  Dry contacts control  Page 7
5.2  Voltage control  Page 7
5.3  Single dry contact control  Page 7
5.4  Priority to open or to close  Page 8
5.5  Emergency control (ESD)  Page 8
5.6  Local control inhibition  Page 9
6  LOCAL CONTROL  Page 10
6.1  Self-holding local control  Page 10
6.2  Local stop  Page 10
6.3  General stop  Page 10
6.4  Local/remote selector padlock  Page 10
7  INDICATIONS  Page 11
7.1  Blinking indications  Page 11
7.2  Indication relay N°1  Page 12
7.3  Indication relay N°2  Page 12
7.4  Indication relay N°3  Page 12
7.5  Indication relay N°4  Page 13
7.6  Fault monitoring relay  Page 13
8  FUSES PROTECTION  Page 15
9  POSITIONER OPTION  Page 15
9.1  Input signal configuration  Page 15
9.1.1  Operation with signal 0-20mA  Page 15
9.1.2  Operation with signal 0-10V  Page 15
9.2  Operation direction configuration  Page 15
9.3  ‘Stay put’ function configuration  Page 16
9.4  Dead band adjustment  Page 16
9.5  Local operation  Page 16
9.6  Adjustment of 0%  Page 17
9.7  Adjustment of 100%  Page 17
9.8  Split range  Page 17
9.9  Operation with 4-20mA transmitter  Page 18
9.10  Remote control AUTO/ON-OFF  Page 18
10  LOCAL INDICATION OPTION  Page 18
11  TIMING CONTROL BOARD OPTION  Page 18
12  TROUBLESHOOTING INTEGRAL+ VERSION  Page 20
13  TROUBLESHOOTING OF POSITIONER VERSION  Page 23
14  USER’S SETTING  Page 50

LINK DOWNLOAD

Chuyên mục: C. Bài giảng C. Bài giảng chuyên ngành Điện - Điện tử (Electrical & Electronic) C. Bài giảng kỹ thuật