%20(1)%20(1).png)
ISO 12161 : 2006 Road vehicles — Endurance braking systems of motor vehicles and towed vehicles — Test procedures
.png)
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Contents Page
Foreword............................................................................................................................................................ iv
Introduction........................................................................................................................................................ v
1 Scope ..................................................................................................................................................... 1
2 Normative references........................................................................................................................... 1
3 Terms and definitions........................................................................................................................... 1
4 Symbols and abbreviated terms ......................................................................................................... 5
5 General test conditions........................................................................................................................ 6
5.1 Ambient conditions .............................................................................................................................. 6
5.2 Test site ................................................................................................................................................. 6
5.3 Vehicle preparation............................................................................................................................... 6
6 Downhill test.......................................................................................................................................... 7
6.1 General................................................................................................................................................... 7
6.2 Downhill test track................................................................................................................................ 8
6.3 Normal test parameters........................................................................................................................ 8
6.4 Determination of specific test parameters......................................................................................... 9
6.5 Conducting the downhill test ............................................................................................................ 12
6.6 Presentation of results....................................................................................................................... 14
7 Drag test (gradient simulation test).................................................................................................. 14
7.1 General................................................................................................................................................. 14
7.2 Drag test track..................................................................................................................................... 14
7.3 Regular test parameters..................................................................................................................... 14
7.4 Determination of specific test parameters....................................................................................... 15
7.5 Conducting the drag test ................................................................................................................... 15
7.6 Data processing and presentation of results .................................................................................. 16
8 Indoor vehicle test on a test bench (gradient simulation test)...................................................... 17
8.1 General................................................................................................................................................. 17
8.2 Description of the test bench ............................................................................................................ 17
8.3 Normal test parameters...................................................................................................................... 18
8.4 Determination of specific test parameters....................................................................................... 19
8.5 Conducting the dynamometer test ................................................................................................... 19
8.6 Data processing and presentation of results .................................................................................. 20
Annex A (normative) Vehicle data.................................................................................................................. 22
Annex B (normative) Test reports .................................................................................................................. 23
Bibliography
LƯU Ý:
Tài liệu được chia sẻ bởi Anh "Quocphong Nguyen" Admin Group "Free Load Tài Liệu" và chỉ được dùng phục vụ mục đích học tập và nghiên cứu.
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Contents Page
Foreword............................................................................................................................................................ iv
Introduction........................................................................................................................................................ v
1 Scope ..................................................................................................................................................... 1
2 Normative references........................................................................................................................... 1
3 Terms and definitions........................................................................................................................... 1
4 Symbols and abbreviated terms ......................................................................................................... 5
5 General test conditions........................................................................................................................ 6
5.1 Ambient conditions .............................................................................................................................. 6
5.2 Test site ................................................................................................................................................. 6
5.3 Vehicle preparation............................................................................................................................... 6
6 Downhill test.......................................................................................................................................... 7
6.1 General................................................................................................................................................... 7
6.2 Downhill test track................................................................................................................................ 8
6.3 Normal test parameters........................................................................................................................ 8
6.4 Determination of specific test parameters......................................................................................... 9
6.5 Conducting the downhill test ............................................................................................................ 12
6.6 Presentation of results....................................................................................................................... 14
7 Drag test (gradient simulation test).................................................................................................. 14
7.1 General................................................................................................................................................. 14
7.2 Drag test track..................................................................................................................................... 14
7.3 Regular test parameters..................................................................................................................... 14
7.4 Determination of specific test parameters....................................................................................... 15
7.5 Conducting the drag test ................................................................................................................... 15
7.6 Data processing and presentation of results .................................................................................. 16
8 Indoor vehicle test on a test bench (gradient simulation test)...................................................... 17
8.1 General................................................................................................................................................. 17
8.2 Description of the test bench ............................................................................................................ 17
8.3 Normal test parameters...................................................................................................................... 18
8.4 Determination of specific test parameters....................................................................................... 19
8.5 Conducting the dynamometer test ................................................................................................... 19
8.6 Data processing and presentation of results .................................................................................. 20
Annex A (normative) Vehicle data.................................................................................................................. 22
Annex B (normative) Test reports .................................................................................................................. 23
Bibliography
LƯU Ý:
Tài liệu được chia sẻ bởi Anh "Quocphong Nguyen" Admin Group "Free Load Tài Liệu" và chỉ được dùng phục vụ mục đích học tập và nghiên cứu.
%20(1).png "Hướng dẫn download ti liệu")
.png "Hướng dẫn download ti liệu")
%20(1).png "Gói VIP Member EBOOKBKMT - Hỗ trợ tài liệu nhanh nhất, ưu tiên cho thành viên VIP (Update 2025)")
.png "Ảnh hưởng của mất nước thẩm thấu và sấy không khí nóng lên chất lượng của đu đủ (Nguyễn Thị Huỳnh Kim) Full")
Không có nhận xét nào: